Glass Aluminum Door Model 452

Wayne Dalton’s Aluminum Full-View commercial door Model 452 features optional insulated, polyurethane-filled rails and stiles which give it an R-value* up to 3.25. This sectional door is insulated, weather-resistant and virtually maintenance free, and is ideal for applications that require a commercial sectional door such as auto dealerships, car washes, and restaurant patios.

 

With a variety of finish and glass options, our Aluminum Full-View doors help create a pleasant interior environment while offering a warm and open look from the exterior.

 

* Wayne Dalton uses a calculated door section R-value for insulated doors.

Key Product Features

  • Max Width: 22’2” (6,705.6mm)
  • Max Height: 14’1”  (4,297.7mm)
  • Door Assembly: Stile and rail assembly of aluminum alloy 6063-T6, 1 3/8″ thick stiles and rails, joined with self tapping screws.
  • Air Infiltration: Meets IECC® requirements for air infiltration with 3rd party tested values below 0.4 cfm/ft2.
  • Rails: Top and bottom rails with 3 1/2″ wide, lower intermediate rail 1 3/8″, upper rail 1 5/8″, minimum wall thickness 0.062″.
  • Stiles: Single end stiles are 3 1/2″ wide, center stile 3″ wide, minimum wall thickness 0.062″.
  • Springs: 10,000 cycles
  • Glazing: 1/8″ (3mm) in 9 options, 1/4″ (6 mm) in 5 options, 1/2″ (13 mm) in 4 options, 5/8″ (16 mm) in 3 options.
  • Finish: Clear anodized.
  • Wind Load: Provide to meet the design/performance requirements specified.
  • Lock: Interior mounted slide lock.
  • Weatherstripping: Flexible bulb-type strip at bottom section.
  • Track: Provide track as recommended by manufacturer to suit loading required and clearances available.
  • Manual Operation: Pull rope or chain hoist.
  • Electric Motor: Provide UL listed electric operator, equal to Genie Commercial Operators, size and type as recommended by manufacturer to move door in either direction at not less than 2/3 foot or more than 1 foot per second.

Door Construction

 

  1. Aluminum glazing stop
  2.  Large glass panels allow maximum light and visibility
  3.  1-3/8” thick section with special reinforcing design
  4.  Vinyl seal between sections
  5.  2-1/4” integrated reinforcing rib on upper intermediate rail for doors 10’3” wide and over
  6.  Aluminum panels that match the rail color available.
  7.  Flexible vinyl bottom door seal

 

Optional Insulated Frame

Polyurethane-filled stiles and rails adds R-value* up to 3.97

Polyurethane insulation in the rails and stiles are an available option. Polyurethane insulation fills the entire cavity and offers better R-value per inch than polystyrene insulation.

*Wayne Dalton uses a calculated door section R-value for our insulated doors.

Glass Options

Low E

Clear Wire

Bronze Tinted

Gray Tinted

Clear (1/8″ standard)

Solid aluminum panels may be specified in lieu of glass. Polycarbonate, various glass thicknesses and custom glazing also available.

Options & Accessories

  • Lock options: interior mounted slide lock with interlock switch for automatic operator, keyed lock, keyed lock with interlock switch for automatic operator.
  • Weather stripping: jamb and header seals.
  • Wind load: available up to ±30 psf, up to 16’2” wide

 

Wind Safe logo for Commercial Glass Aluminum Doors 

*Static (Non-Impact) Wind Load designs are based on engineering analysis and although not certified by FBC, TDI, or Miami-Dade, the designs are compliant with the 2015 IBC.

Operation Options

  • Pull rope
  • Chain hoist
  • Electric operator

Spring Options

  • 10,000 cycles (standard)
  • 25,000 cycles
  • 50,000 cycles
  • 100,000 cycles

Finishes

Anodized
Clear (standard)

Bronze

Black

Powder Coat Finishes

Clear

Bronze

Brown

Black

RAL Powder Coat

Wayne Dalton also offers approximately 200 powder coat options to complement the exterior colors of a building.

 

 

Online color swatches are only digital reproductions of actual standards and will vary in appearance due to differences in monitor and video card output. These digital representations should not be used to finalize color selection(s).

FEATURES

Key Product Features

  • Max Width: 22’2” (6,705.6mm)
  • Max Height: 14’1”  (4,297.7mm)
  • Door Assembly: Stile and rail assembly of aluminum alloy 6063-T6, 1 3/8″ thick stiles and rails, joined with self tapping screws.
  • Air Infiltration: Meets IECC® requirements for air infiltration with 3rd party tested values below 0.4 cfm/ft2.
  • Rails: Top and bottom rails with 3 1/2″ wide, lower intermediate rail 1 3/8″, upper rail 1 5/8″, minimum wall thickness 0.062″.
  • Stiles: Single end stiles are 3 1/2″ wide, center stile 3″ wide, minimum wall thickness 0.062″.
  • Springs: 10,000 cycles
  • Glazing: 1/8″ (3mm) in 9 options, 1/4″ (6 mm) in 5 options, 1/2″ (13 mm) in 4 options, 5/8″ (16 mm) in 3 options.
  • Finish: Clear anodized.
  • Wind Load: Provide to meet the design/performance requirements specified.
  • Lock: Interior mounted slide lock.
  • Weatherstripping: Flexible bulb-type strip at bottom section.
  • Track: Provide track as recommended by manufacturer to suit loading required and clearances available.
  • Manual Operation: Pull rope or chain hoist.
  • Electric Motor: Provide UL listed electric operator, equal to Genie Commercial Operators, size and type as recommended by manufacturer to move door in either direction at not less than 2/3 foot or more than 1 foot per second.

Door Construction

 

  1. Aluminum glazing stop
  2.  Large glass panels allow maximum light and visibility
  3.  1-3/8” thick section with special reinforcing design
  4.  Vinyl seal between sections
  5.  2-1/4” integrated reinforcing rib on upper intermediate rail for doors 10’3” wide and over
  6.  Aluminum panels that match the rail color available.
  7.  Flexible vinyl bottom door seal

 

Optional Insulated Frame

Polyurethane-filled stiles and rails adds R-value* up to 3.97

Polyurethane insulation in the rails and stiles are an available option. Polyurethane insulation fills the entire cavity and offers better R-value per inch than polystyrene insulation.

*Wayne Dalton uses a calculated door section R-value for our insulated doors.

DOOR OPTIONS

Glass Options

Low E

Clear Wire

Bronze Tinted

Gray Tinted

Clear (1/8″ standard)

Solid aluminum panels may be specified in lieu of glass. Polycarbonate, various glass thicknesses and custom glazing also available.

Options & Accessories

  • Lock options: interior mounted slide lock with interlock switch for automatic operator, keyed lock, keyed lock with interlock switch for automatic operator.
  • Weather stripping: jamb and header seals.
  • Wind load: available up to ±30 psf, up to 16’2” wide

 

Wind Safe logo for Commercial Glass Aluminum Doors 

*Static (Non-Impact) Wind Load designs are based on engineering analysis and although not certified by FBC, TDI, or Miami-Dade, the designs are compliant with the 2015 IBC.

Operation Options

  • Pull rope
  • Chain hoist
  • Electric operator

Spring Options

  • 10,000 cycles (standard)
  • 25,000 cycles
  • 50,000 cycles
  • 100,000 cycles
COLORS

Finishes

Anodized
Clear (standard)

Bronze

Black

Powder Coat Finishes

Clear

Bronze

Brown

Black

RAL Powder Coat

Wayne Dalton also offers approximately 200 powder coat options to complement the exterior colors of a building.

 

 

Online color swatches are only digital reproductions of actual standards and will vary in appearance due to differences in monitor and video card output. These digital representations should not be used to finalize color selection(s).

DOCUMENTS
WARRANTY

CALL NOW (405) 720-7107
DOORTEC TECHNICIANS ARE READY
TO ANSWER YOUR QUESTIONS

WE ARE HAPPY TO HELP!