Rolling Service Door Model 800

Model 800 Rolling Service Door is designed to meet the tough requirements of virtually any commercial or industrial application. Model 800 offers flexibility in substrate materials with choices of galvanized or prime steel, stainless steel, or aluminum.

Our Model 800 rolling service doors are composed of curved or flat-faced slats that provide a natural water-shed, helping to reduce corrosion. The slats are designed with free-acting interlocking joints that permit easy articulation when the door coils.

Model 800 features a strong double-angle bottom bar designed for easy installation and does not require fasteners protruding into the guide openings, so the bottom bar does not interfere with door operation.

Counterbalance assembly consists of a spring barrel which serves as a load-carrying beam. It encases the counterbalance mechanism and provides the axis around which the curtain coils. (Deflection is limited to 0.033″ per lineal foot of span.)

FEATURES
DOOR OPTIONS
COLORS
DOCUMENTS
WARRANTY

Key Product Features

Max Width*: 42’
Max Height*: 40’
Max Steel Gauge = 16
Steel, aluminum or stainless steel construction
Heavy-duty 3” flat or curved slats
Wind load ±20 psf standard; options up to ±55 psf
Double-angle bottom bar reinforces the lower edge of the curtain

*Larger sizes may be available. Maximum height and maximum width are independent of each other and may vary based on slat profile, material and gauge.

Common Applications

Warehouse and Industrial spaces
Manufacturing facilities
Food and Beverage facilities

No. 4 Slat Profile

Standard:

Curved slat, 22-gauge steel

Available:

Up to 16-gauge steel
Up to 18-gauge stainless steel
Up to 14-gauge aluminum

Pitch*: 2.76″

No. 14 Slat Profile Secur-Vent®

Available:

Perforated slat with 1/16 diameter holes
20-gauge steel or stainless steel
Offers 20-25% open area over slat
Up to 22 wide by 20 high door size

Pitch*: 2.45″

No. 14 Slat Profile

Standard:

Flat slat, 22-gauge steel

Available:

Up to 16-gauge steel
Up to 18-gauge stainless steel
Up to 14-gauge aluminum (mill, clear, or
bronze anodized)

Pitch*: 2.45″

No. 14 Slat Profile Ventilated

Available:

6″ curved slat, 18-gauge primed steel
Up to 14-gauge steel available

Pitch*: 6.15″

Options & Accessories

Curtain: steel, stainless steel, aluminum, G-90 galvanized
Locking: slide bolts, cylinder, best lock, thumb turns
Bottom bar: stainless steel double angle, structural steel angle construction (galvanized steel only), extruded aluminum, sloped
Bottom edge: astragal, pneumatic or electric sensing edge
Spring: up to 200k cycle, options available dependent on door size and weight
Perimeter seals: angled guide brush seal, clip-on vinyl guide seal, exterior lintel weather seal, interior weather baffle
End covers
Fascia
Drop stop device
Pass door
Vision slat

Operation Options

Manual push up
Crank (awning, wall)
Chain hoist
Motor
Through wall

Wind Load Options

Wind locks alternating or continuous with windbar
Articulating Windlocks for Operational wind load
Options available to meet up to Dade County – Florida Building Commission High Velocity Hurricane Zone (FBC HVHZ)

Color Options

White

Gray

Beige

Brown

*18-ga. and 20-ga. doors are only available in gray.

RAL Powder Coat

Wayne Dalton also offers approximately 200 powder coat options to complement the exterior colors of a building.

Online color swatches are only digital reproductions of actual standards and will vary in appearance due to differences in monitor and video card output. These digital representations should not be used to finalize color selection(s).

Documents

Model 800 Brochure

Rolling Door Systems Brochure

Rolling Door End User Manual

Wind Load Options 800