Rolling Steel Fire Door - Model 700

FireStar® Model 700 Rolling Steel Fire Doors provide a practical and innovative solution to safety and fire protection. FireStar® doors can be drop-tested and reset at any time by anyone, thanks to a standard auto-reset feature. This door features a forward-thinking design that outperforms industry standard fire doors in all areas, including auto-reset testing capability; smooth, quiet operation; and reliable, long-lasting performance.

The revolutionary FireStar® design uses a patent-pending planetary gear on the drop-out mechanism ensuring years of reliable service and drop-out performance. Factory-tested and approved for a minimum of 20,000 cycles, the FireStar® door can be used and tested on a regular basis without concerns of premature failure. Our fire doors have been tested and approved to meet the requirements of well-known agencies, such as Underwriters Laboratories and Factory Mutual, and conform to NFPA Standard 80.

We incorporate one standardized component design for all FireStar®* doors regardless of size, and utilize fewer parts than other models. This helps to ensure more accurate installations and reduces the possibility of potential service calls in the future.

*Doors up to 24’x24’

Key Product Features

  • Max Height: 24’ (7,315.2 mm)
  • Max Width: 24’ (7,7315.2 mm)
  • Max Square Foot: 324 sq. ft.
  • Material: Galvanized or Stainless Steel
  • Curtain: Interlocking roll-formed slats with alternate slats fitted with metal endlocks / windlocks
  • Operation: Lift-up standard. Chain hoist included on sizes that require it
  • Bottom Bar: Two equal angles, 0.121″ min thickness, to stiffen curtain
  • Brackets: Enclose ends of coil and provide support for counterbalance pipe at each end. Fabricate of steel plates with permanently sealed ball bearing
  • Counter Balance: Curtain to be correctly balanced by helical springs, oil tempered torsion type. Cast iron barrel plugs will be used to anchor springs to tension shaft and pipe 20,000 cycle
  • Hood: Minimum 24-gauge galvanized or stainless steel hood fabricated of sheet metal, flanged at top for attachment to header and flanged at bottom to provide lonitudinal stiffness
  • Finish: Rust inhibitive primer or non-galvanized surfaces and operating mechanisms. Guides and brackets will be coated with a flat black prime paint.
  • Operator Options: Chain Hoist with gear drive reduction, wall crank box, motor operation, motor operation with electrical sensing edge, motor operation with pneumatic sensing edge
  • Release Mechanism: FireSTar release mechanism standard on doors up to 24′ x 24′
  • Mounting: Structural drive, drywall over wood stud jamb, drywall over 16-gauge steel stud jamb.
*Maximum height and maximum width are independent of each other and may vary based on slat profile, material and gauge.

Slat Profiles

No. 2 – Standard: Curved-faced single crown slat. Available: Up to 20-gauge steel Up to 20-gauge stainless steel Pitch: 1.9′

 

No. 4 – Standard: Curved-faced single crown slat. Available: Up to 18-gauge steel Up to 20-gauge stainless steel Pitch: 2.8′

 

 

No. 14 – Standard: Flat-faced slat. Available: Up to 18-gauge steel Up to 18-gauge stainless steel Pitch: 2.45′

 

 

No. 17 – Standard: Flat-faced slat. Available: Up to 20-gauge steel Up to 20-gauge stainless steel Pitch: 1.6′

 

FireStar Door Control Devices

Chain hoist, motor and crank operation

  • Revolutionary fire door control device utilizing a patented planetary gear arrangement to disconnect the operator and drop the door in the event of a fire
  • Easy drop test and reset a fire door without resetting spring tension and rerouting cables.

Lift up operation

  • Revolutionary fire door control device utilizing a clutch plates and unique counterbalance technology to drop the door in the event of a fire.

 

Options & Accessories

  • Operator Options: Chain hoist with gear drive reduction; awning crank; motor operation with electrical or pneumatic sensing edge
  • FM label option to include hood with steel baffle
  • Wind load options available
  • Viscous governor, if required by size of door
  • 22-gauge hood

Color Options

White

Gray

Beige

Brown

RAL Powder Coat

Wayne Dalton also offers approximately 200 powder coat options to complement the exterior colors of a building.

 

 

Online color swatches are only digital reproductions of actual standards and will vary in appearance due to differences in monitor and video card output. These digital representations should not be used to finalize color selection(s).

FEATURES

Key Product Features

  • Max Height: 24’ (7,315.2 mm)
  • Max Width: 24’ (7,7315.2 mm)
  • Max Square Foot: 324 sq. ft.
  • Material: Galvanized or Stainless Steel
  • Curtain: Interlocking roll-formed slats with alternate slats fitted with metal endlocks / windlocks
  • Operation: Lift-up standard. Chain hoist included on sizes that require it
  • Bottom Bar: Two equal angles, 0.121″ min thickness, to stiffen curtain
  • Brackets: Enclose ends of coil and provide support for counterbalance pipe at each end. Fabricate of steel plates with permanently sealed ball bearing
  • Counter Balance: Curtain to be correctly balanced by helical springs, oil tempered torsion type. Cast iron barrel plugs will be used to anchor springs to tension shaft and pipe 20,000 cycle
  • Hood: Minimum 24-gauge galvanized or stainless steel hood fabricated of sheet metal, flanged at top for attachment to header and flanged at bottom to provide lonitudinal stiffness
  • Finish: Rust inhibitive primer or non-galvanized surfaces and operating mechanisms. Guides and brackets will be coated with a flat black prime paint.
  • Operator Options: Chain Hoist with gear drive reduction, wall crank box, motor operation, motor operation with electrical sensing edge, motor operation with pneumatic sensing edge
  • Release Mechanism: FireSTar release mechanism standard on doors up to 24′ x 24′
  • Mounting: Structural drive, drywall over wood stud jamb, drywall over 16-gauge steel stud jamb.
*Maximum height and maximum width are independent of each other and may vary based on slat profile, material and gauge.

Slat Profiles

No. 2 – Standard: Curved-faced single crown slat. Available: Up to 20-gauge steel Up to 20-gauge stainless steel Pitch: 1.9′

 

No. 4 – Standard: Curved-faced single crown slat. Available: Up to 18-gauge steel Up to 20-gauge stainless steel Pitch: 2.8′

 

 

No. 14 – Standard: Flat-faced slat. Available: Up to 18-gauge steel Up to 18-gauge stainless steel Pitch: 2.45′

 

 

No. 17 – Standard: Flat-faced slat. Available: Up to 20-gauge steel Up to 20-gauge stainless steel Pitch: 1.6′

 

FireStar Door Control Devices

Chain hoist, motor and crank operation

  • Revolutionary fire door control device utilizing a patented planetary gear arrangement to disconnect the operator and drop the door in the event of a fire
  • Easy drop test and reset a fire door without resetting spring tension and rerouting cables.

Lift up operation

  • Revolutionary fire door control device utilizing a clutch plates and unique counterbalance technology to drop the door in the event of a fire.

 

DOOR OPTIONS

Options & Accessories

  • Operator Options: Chain hoist with gear drive reduction; awning crank; motor operation with electrical or pneumatic sensing edge
  • FM label option to include hood with steel baffle
  • Wind load options available
  • Viscous governor, if required by size of door
  • 22-gauge hood
COLORS

Color Options

White

Gray

Beige

Brown

RAL Powder Coat

Wayne Dalton also offers approximately 200 powder coat options to complement the exterior colors of a building.

 

 

Online color swatches are only digital reproductions of actual standards and will vary in appearance due to differences in monitor and video card output. These digital representations should not be used to finalize color selection(s).

DOCUMENTS
WARRANTY

CALL NOW (405) 720-7107
DOORTEC TECHNICIANS ARE READY
TO ANSWER YOUR QUESTIONS

WE ARE HAPPY TO HELP!